Introduction
This document describes how to configure the Cisco AnyConnect Secure Mobility Client via the Cisco Adaptive Security Device Manager (ASDM) on a Cisco Adaptive Security Appliance (ASA) that runs software Version 9.3(2).
Prerequisites
Requirements
The Cisco AnyConnect Secure Mobility Client web deployment package should be downloaded to the local desktop from which the ASDM access to the ASA is present. In order to download the client package, refer to the Cisco AnyConnect Secure Mobility Client web page. The web deployment packages for various Operating Systems (OSs) can be uploaded to the ASA at the same time.
These are the web deployment file names for the various OSs:
- Microsoft Windows OSs – AnyConnect-win-<version>-k9.pkg
- Macintosh (MAC) OSs – AnyConnect-macosx-i386-<version>-k9.pkg
- Linux OSs – AnyConnect-linux-<version>-k9.pkg
Components Used
The information in this document is based on these software and hardware versions:
- ASA Version 9.3(2)
- ASDM Version 7.3(1)101
- AnyConnect Version 3.1
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Background Information
This document provides step-by-step details about how to use the Cisco AnyConnect Configuration Wizard via the ASDM in order to configure the AnyConnect Client and enable split tunneling.
Split-tunneling is used in scenarios where only specific traffic must be tunneled, opposed to scenarios where all of the client machine-generated traffic flows across the VPN when connected. Use of the AnyConnect Configuration Wizard will by default result in a tunnel-all configuration on the ASA. Split tunnelling must be configured separately, which is explained in further detail in the Split Tunnel section of this document.
In this configuration example, the intention is to send traffic for the 10.10.10.0/24 subnet, which is the LAN subnet behind the ASA, over the VPN tunnel and all other traffic from the client machine is forwarded via its own Internet circuit.
AnyConnect License Information
Here are some links to useful information about the Cisco AnyConnect Secure Mobility Client licenses:
- Refer to the AnyConnect Secure Mobility Client Features, Licenses, and OSs, Release 3.1 document in order to determine the licenses that are required for AnyConnect Secure Mobility Client and the related features.
- Refer to the Cisco AnyConnect Ordering Guide for information about AnyConnect Apex and Plus licenses.
- Refer to the What ASA License Is Needed for IP Phone and Mobile VPN Connections? document for information about the additional license requirements for IP phone and mobile connections.
Configure
This section describes how to configure the Cisco AnyConnect Secure Mobility Client on the ASA.
Network Diagram
This is the topology that is used for the examples in this document:
ASDM AnyConnect Configuration Wizard
The AnyConnect Configuration Wizard can be used in order to configure the AnyConnect Secure Mobility Client. Ensure that an AnyConnect client package has been uploaded to the flash/disk of the ASA Firewall before you proceed.
Complete these steps in order to configure the AnyConnect Secure Mobility Client via the Configuration Wizard:
- Log into the ASDM, launch the Configuration Wizard, and click Next:
- Enter the Connection Profile Name, choose the interface on which the VPN will be terminated from the VPN Access Interface drop down menu, and click Next:
- Check the SSL check box in order to enable Secure Sockets Layer (SSL). The Device Certificate can be a trusted third party Certificate Authority (CA) issued certificate (such as Verisign, or Entrust), or a self-signed certificate. If the certificate is already installed on the ASA, then it can be chosen via the drop down menu.
In order to install a third-party certificate, complete the steps that are described in the ASA 8.x Manually Install 3rd Party Vendor Certificates for use with WebVPN Configuration Example Cisco document.
- Click Add:
- Type an appropriate name into the Trustpoint Name field, and click the Add a new identity certificate radio button. If there are no Rivest-Shamir-Addleman (RSA) key pairs present on the device, click New in order to generate one:
- Click the Use default key pair name radio button, or click the Enter new key pair name radio button and enter a new name. Select the size for the keys, and then click Generate Now:
- After the RSA key pair is generated, choose the key and check the Generate self-signed certificate check box. Enter the desired subject Domain Name (DN) into the Certificate Subject DN field, and then click Add Certificate:
- Once the enrollment is complete, click OK, OK, and then Next:
- Click Add in order to add the AnyConnect Client image (the .pkg file) from the PC or from the flash. Click Browse Flash in order to add the image from the flash drive, or click Upload in order to add the image from the host machine directly:
- Once the image is added, click Next:
- The user authentication can be completed via the Authentication, Authorization, and Accounting (AAA) server groups. If the users are already configured, then choose LOCAL and click Next.
- The address pool for the VPN client must be configured. If one is already configured, then select it from the drop down menu. If not, click New in order to configure a new one. Once complete, click Next:
- Input the Domain Name System (DNS) servers and DNs into the DNS and Domain Name fields appropriately, and then click Next:
- In this scenario, the objective is to restrict access over the VPN to the 10.10.10.0/24 network that is configured as the Inside (or LAN) subnet behind the ASA. The traffic between the client and the inside subnet must be exempt from any dynamic Network Address Translation (NAT).
Check the Exempt VPN traffic from network address translation check box and configure the LAN and WAN interfaces that will be used for the exemption: - Choose the local networks that must be exempt:
- Click Next, Next, and then Finish.
The AnyConnect Client configuration is now complete. However, when you configure AnyConnect via the Configuration Wizard, it configures the Split Tunnel policy as Tunnelall by default. In order to tunnel specific traffic only, split-tunneling must be implemented.
Only the traffic that is destined to the ASA WAN (or Outside) IP address will bypass the tunneling on the client machine. This can be seen in the output of the route print command on Microsoft Windows machines.
Split Tunnel Configuration
Split tunnelling is a feature that you can use in order to define the traffic for the subnets or hosts that must be encrypted. This involves the configuration of an Access Control List (ACL) that will be associated with this feature. The traffic for the subnets or hosts that is defined on this ACL will be encrypted over the tunnel from the client-end, and the routes for these subnets are installed on the PC routing table.
Complete these steps in order to move from the Tunnel-all configuration to the Split-tunnel configuration:
- Navigate to Configuration > Remote Access VPN > Group Policies:
- Click Edit, and use the navigation tree in order to navigate to Advanced > Split Tunneling. Uncheck the Inherit check box in the Policy section, and select Tunnel Network List Below from the drop down menu:
- Uncheck the Inherit check box in the Network List section, and click Manage in order to select the ACL that specifies the LAN network(s) to which the client needs access:
- Click Standard ACL, Add, Add ACL, and then ACL name:
- Click Add ACE in order to add the rule:
- Click OK.
- Click Apply.
Once connected, the routes for the subnets or hosts on the split ACL are added to the routing table of the client machine. On Microsoft Windows machines, this can be viewed in the output of the route print command. The next hop for these routes will be an IP address from the client IP pool subnet (usually the first IP address of the subnet):
C:\Users\admin>route print IPv4 Route Table ====================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.106.44.1 10.106.44.243 261 10.10.10.0 255.255.255.0 10.10.11.2 10.10.11.1 2 !! This is the split tunnel route. 10.106.44.0 255.255.255.0 On-link 10.106.44.243 261 172.16.21.1 255.255.255.255 On-link 10.106.44.243 6 !! This is the route for the ASA Public IP Address.
On MAC OS machines, enter the netstat -r command in order to view the PC routing table:
$ netstat -r Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire default hsrp-64-103-236-1. UGSc 34 0 en1 10.10.10/24 10.10.11.2 UGSc 0 44 utun1 !! This is the split tunnel route. 10.10.11.2/32 localhost UGSc 1 0 lo0 172.16.21.1/32 hsrp-64-103-236-1. UGSc 1 0 en1 !! This is the route for the ASA Public IP Address.
Download and Install AnyConnect Client
There are two methods that you can use in order to deploy Cisco AnyConnect Secure Mobility Client on the user machine:
- Web deployment
- Standalone deployment
Both of these methods are explained in greater detail in the sections that follow.
Web Deployment
In order to use the web deployment method, enter the https://<ASA FQDN>or<ASA IP> URL into a browser on the client machine, which brings you to the WebVPN portal page.
Once logged into the page, the installation should begin on the client machine, and the client should connect to the ASA after the installation is complete.
Standalone Deployment
Complete these steps in order to use the standalone deployment method:
- Download the AnyConnect Client image from the Cisco website. In order to choose the correct image for download, refer to the Cisco AnyConnect Secure Mobility Client web page. A download link is provided on this page. Navigate to the download page and select the appropriate version. Perform a search for Full installation package - Window / Standalone installer (ISO).
- Use WinRar or 7-Zip in order to extract the contents of the ISO package:
- Once the contents are extracted, run the Setup.exe file and choose the modules that must be installed along with Cisco AnyConnect Secure Mobility Client.
CLI Configuration
This section provides the CLI configuration for the Cisco AnyConnect Secure Mobility Client for reference purposes.
ASA Version 9.3(2) ! hostname PeerASA-29 enable password 8Ry2YjIyt7RRXU24 encrypted ip local pool SSL-Pool 10.10.11.1-10.10.11.20 mask 255.255.255.0 ! interface GigabitEthernet0/0 nameif outside security-level 0 ip address 172.16.21.1 255.255.255.0 ! interface GigabitEthernet0/1 nameif inside security-level 100 ip address 10.10.10.1 255.255.255.0 ! boot system disk0:/asa932-smp-k8.bin ftp mode passive object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 object network NETWORK_OBJ_10.10.11.0_27 subnet 10.10.11.0 255.255.255.224 access-list all extended permit ip any any !***********Split ACL configuration*********** access-list Split-ACL standard permit 10.10.10.0 255.255.255.0 no pager logging enable logging buffered debugging mtu outside 1500 mtu inside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-721.bin no asdm history enable arp timeout 14400 no arp permit-nonconnected !************** NAT exemption Configuration ***************** !This will exempt traffic from Local LAN(s) to the !Remote LAN(s) from getting NATted on any dynamic NAT rule. nat (inside,outside) source static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 destination static NETWORK_OBJ_10.10.11.0_27 NETWORK_OBJ_10.10.11.0_27 no-proxy-arp route-lookup access-group all in interface outside route outside 0.0.0.0 0.0.0.0 172.16.21.2 1 timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL aaa authentication ssh console LOCAL http server enable http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact !********** Trustpoint for Selfsigned certificate*********** !Genarate the key pair and then configure the trustpoint !Enroll the trustpoint genarate the self-signed certificate crypto ca trustpoint SelfsignedCert enrollment self subject-name CN=anyconnect.cisco.com keypair sslcert crl configure crypto ca trustpool policy crypto ca certificate chain SelfsignedCert certificate 4748e654 308202f0 308201d8 a0030201 02020447 48e65430 0d06092a 864886f7 0d010105 0500303a 311d301b 06035504 03131461 6e79636f 6e6e6563 742e6369 73636f2e 636f6d31 19301706 092a8648 86f70d01 0902160a 50656572 4153412d 3239301e 170d3135 30343032 32313534 30375a17 0d323530 33333032 31353430 375a303a 311d301b 06035504 03131461 6e79636f 6e6e6563 742e6369 73636f2e 636f6d31 19301706 092a8648 86f70d01 0902160a 50656572 4153412d 32393082 0122300d 06092a86 4886f70d 01010105 00038201 0f003082 010a0282 010100f6 a125d0d0 55a975ec a1f2133f 0a2c3960 0da670f8 bcb6dad7 efefe50a 482db3a9 7c6db7c4 ed327ec5 286594bc 29291d8f 15140bad d33bc492 02f5301e f615e7cd a72b60e0 7877042b b6980dc7 ccaa39c8 c34164d9 e2ddeea1 3c0b5bad 5a57ec4b d77ddb3c 75930fd9 888f92b8 9f424fd7 277e8f9e 15422b40 071ca02a 2a73cf23 28d14c93 5a084cf0 403267a6 23c18fa4 fca9463f aa76057a b07e4b19 c534c0bb 096626a7 53d17d9f 4c28a3fd 609891f7 3550c991 61ef0de8 67b6c7eb 97c3bff7 c9f9de34 03a5e788 94678f4d 7f273516 c471285f 4e23422e 6061f1e7 186bbf9c cf51aa36 19f99ab7 c2bedb68 6d182b82 7ecf39d5 1314c87b ffddff68 8231d302 03010001 300d0609 2a864886 f70d0101 05050003 82010100 d598c1c7 1e4d8a71 6cb43296 c09ea8da 314900e7 5fa36947 c0bc1778 d132a360 0f635e71 400e592d b27e29b1 64dfb267 51e8af22 0a6a8378 5ee6a734 b74e686c 6d983dde 54677465 7bf8fe41 daf46e34 bd9fd20a bacf86e1 3fac8165 fc94fe00 4c2eb983 1fc4ae60 55ea3928 f2a674e1 8b5d651f 760b7e8b f853822c 7b875f91 50113dfd f68933a2 c52fe8d9 4f9d9bda 7ae2f750 313c6b76 f8d00bf5 1f74cc65 7c079a2c 8cce91b0 a8cdd833 900a72a4 22c2b70d 111e1d92 62f90476 6611b88d ff58de5b fdaa6a80 6fe9f206 3fe4b836 6bd213d4 a6356a6c 2b020191 bf4c8e3d dd7bdd8b 8cc35f0b 9ad8852e b2371ee4 23b16359 ba1a5541 ed719680 ee49abe8 quit telnet timeout 5 ssh timeout 5 ssh key-exchange group dh-group1-sha1 console timeout 0 management-access inside threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ssl server-version tlsv1-only ssl encryption des-sha1 3des-sha1 aes128-sha1 aes256-sha1 !******** Bind the certificate to the outside interface******** ssl trust-point SelfsignedCert outside !********Configure the Anyconnect Image and enable Anyconnect*** webvpn enable outside anyconnect image disk0:/anyconnect-win-3.1.06073-k9.pkg 1 anyconnect enable tunnel-group-list enable !*******Group Policy configuration********* !Tunnel protocol, Spit tunnel policy, Split !ACL, etc. can be configured. group-policy GroupPolicy_SSLClient internal group-policy GroupPolicy_SSLClient attributes wins-server none dns-server value 10.10.10.23 vpn-tunnel-protocol ikev2 ssl-client split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-ACL default-domain value Cisco.com username User1 password PfeNk7qp9b4LbLV5 encrypted username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 15 !*******Tunnel-Group (Connection Profile) Configuraiton***** tunnel-group SSLClient type remote-access tunnel-group SSLClient general-attributes address-pool SSL-Pool default-group-policy GroupPolicy_SSLClient tunnel-group SSLClient webvpn-attributes group-alias SSLClient enable ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect sip inspect xdmcp ! service-policy global_policy global Cryptochecksum:8d492b10911d1a8fbcc93aa4405930a0 : end
Verify
Complete these steps in order to verify the client connection and the various parameters that are associated to that connection:
- Navigate to Monitoring > VPN on the ASDM:
- You can use the Filter By option in order to filter the type of VPN. Select AnyConnect Client from the drop down menu and all of the AnyConnect Client sessions.
- Double-click a session in order to obtain further details about that particular session:
- Enter the show vpn-sessiondb anyconnect command into the CLI in order to obtain the session details:
# show vpn-sessiondb anyconnect Session Type : AnyConnect Username : cisco Index : 14 Assigned IP : 10.10.11.1 Public IP : 172.16.21.1 Protocol : AnyConnect-Parent SSL-Tunnel DTLS-Tunnel License : AnyConnect Premium Encryption : AnyConnect-Parent: (1)none SSL-Tunnel: (1)3DES DTLS-Tunnel: (1)DES Hashing : AnyConnect-Parent: (1)none SSL-Tunnel: (1)SHA1 DTLS-Tunnel: (1)SHA1 Bytes Tx : 11472 Bytes Rx : 39712 Group Policy : GroupPolicy_SSLClient Tunnel Group : SSLClient Login Time : 16:58:56 UTC Mon Apr 6 2015 Duration : 0h:49m:54s Inactivity : 0h:00m:00s NAC Result : Unknown VLAN Mapping : N/A VLAN : none
- You can use the other filter options in order to refine the results:
# show vpn-sessiondb detail anyconnect filter name cisco Session Type: AnyConnect Detailed Username : cisco Index : 19 Assigned IP : 10.10.11.1 Public IP : 10.106.44.243 Protocol : AnyConnect-Parent SSL-Tunnel DTLS-Tunnel License : AnyConnect Premium Encryption : AnyConnect-Parent: (1)none SSL-Tunnel: (1)3DES DTLS-Tunnel: (1)DES Hashing : AnyConnect-Parent: (1)none SSL-Tunnel: (1)SHA1 DTLS-Tunnel: (1)SHA1 Bytes Tx : 11036 Bytes Rx : 4977 Pkts Tx : 8 Pkts Rx : 60 Pkts Tx Drop : 0 Pkts Rx Drop : 0 Group Policy : GroupPolicy_SSLClient Tunnel Group : SSLClient Login Time : 20:33:34 UTC Mon Apr 6 2015 Duration : 0h:01m:19s AnyConnect-Parent Tunnels: 1 SSL-Tunnel Tunnels: 1 DTLS-Tunnel Tunnels: 1 AnyConnect-Parent: Tunnel ID : 19.1 Public IP : 10.106.44.243 Encryption : none Hashing : none TCP Src Port : 58311 TCP Dst Port : 443 Auth Mode : userPassword Idle Time Out: 30 Minutes Idle TO Left : 29 Minutes Client OS : Windows Client Type : AnyConnect Client Ver : Cisco AnyConnect VPN Agent for Windows 3.1.06073 Bytes Tx : 5518 Bytes Rx : 772 Pkts Tx : 4 Pkts Rx : 1 Pkts Tx Drop : 0 Pkts Rx Drop : 0 SSL-Tunnel: Tunnel ID : 19.2 Assigned IP : 10.10.11.1 Public IP : 10.106.44.243 Encryption : 3DES Hashing : SHA1 Encapsulation: TLSv1.0 TCP Src Port : 58315 TCP Dst Port : 443 Auth Mode : userPassword Idle Time Out: 30 Minutes Idle TO Left : 29 Minutes Client OS : Windows Client Type : SSL VPN Client Client Ver : Cisco AnyConnect VPN Agent for Windows 3.1.06073 Bytes Tx : 5518 Bytes Rx : 190 Pkts Tx : 4 Pkts Rx : 2 Pkts Tx Drop : 0 Pkts Rx Drop : 0 DTLS-Tunnel: Tunnel ID : 19.3 Assigned IP : 10.10.11.1 Public IP : 10.106.44.243 Encryption : DES Hashing : SHA1 Encapsulation: DTLSv1.0 UDP Src Port : 58269 UDP Dst Port : 443 Auth Mode : userPassword Idle Time Out: 30 Minutes Idle TO Left : 30 Minutes Client OS : Windows Client Type : DTLS VPN Client Client Ver : Cisco AnyConnect VPN Agent for Windows 3.1.06073 Bytes Tx : 0 Bytes Rx : 4150 Pkts Tx : 0 Pkts Rx : 59 Pkts Tx Drop : 0 Pkts Rx Drop : 0
Troubleshoot
You can use the AnyConnect Diagnostics and Reporting Tool (DART) in order to collect the data that is useful for troubleshooting AnyConnect installation and connection problems. The DART Wizard is used on the computer that runs AnyConnect. The DART assembles the logs, status, and diagnostic information for the Cisco Technical Assistance Center (TAC) analysis and does not require administrator privileges to run on the client machine.
Install the DART
Complete these steps in order to install the DART:
- Download the AnyConnect Client image from the Cisco website. In order to choose the correct image for download, refer to the Cisco AnyConnect Secure Mobility Client web page. A download link is provided on this page. Navigate to the download page and select the appropriate version. Perform a search for Full installation package - Window / Standalone installer (ISO).
- Use WinRar or 7-Zip in order to extract the contents of the ISO package:
- Browse to the folder to which the contents were extracted.
- Run the Setup.exe file and select only Anyconnect Diagnostic And Reporting Tool:
Run the DART
Here is some important information to consider before you run the DART:
- The issue must be recreated at least once before you run the DART.
- The date and time on the user machine must be noted when the issue is recreated.
Run the DART from the Start Menu on the client machine:
Either Default or Custom mode can be selected. Cisco recommends that you run the DART in the Default mode so that all of the information can be captured in a single shot.
Once completed, the tool saves the DART bundle .zip file to the client desktop. The bundle can then be emailed to the TAC (after you open a TAC case) for further analysis.
No comments:
Post a Comment